# Pulley system on a double inclined plane

This article discusses a scenario/arrangement whose statics/dynamics/kinematics can be understood using the ideas of classical mechanics.

View other mechanics scenarios

This article is about the following scenario. A fixed triangular wedge has two inclines and making angles and with the horizontal, thus making it a double inclined plane. A pulley is affixed to the top vertex of the triangle. A string through the pulley has attached at its two ends blocks of masses and , resting on the two inclines and respectively. The string is inextensible. The coefficients of static and kinetic friction between and are and respectively. The coefficients of static and kinetic friction between and are and respectively. Assume that and .

We assume the pulley to be massless so that its moment of inertia can be ignored for the information below. We also assume the string to be massless, so that the tension values at the two ends of the string are equal in magnitude.

## Contents

## Summary of cases starting from rest

These cases will be justified later in the article, based on the force diagram and by solving the resulting equations.

Case | What happens qualitatively | Magnitude of accelerations |
---|---|---|

slides downward and slides upward, with the same magnitude of acceleration | . | |

slides downward and slides upward, with the same magnitude of acceleration | . | |

The system remains at rest |

## Basic components of force diagram

There are *two* force diagrams of interest here, namely the force diagrams of the masses and .

There are five candidate forces on each mass. We describe the situation for below:

Force (letter) | Nature of force | Condition for existence | Magnitude | Direction |
---|---|---|---|---|

gravitational force | unconditional | where is the mass and is the acceleration due to gravity | vertically downward, hence an angle with the normal to the incline and an angle with the incline | |

tension | unconditional | needs to be computed based on solving equations. | pulls the mass up the inclined plane. | |

normal force | unconditional | adjusts so that there is no net acceleration perpendicular to the plane of the incline | outward normal to the incline | |

static friction | no sliding | adjusts so that there is no net acceleration along the incline. At most equal to . | The direction could be either up or down the incline, depending on whether the remaining forces create a net tendency to pull down or pull it up. | |

kinetic friction | sliding | where is the normal force | opposite direction of motion -- hence down the incline if sliding up, up the incline if sliding down. |

A similar description is valid for :

Force (letter) | Nature of force | Condition for existence | Magnitude | Direction |
---|---|---|---|---|

gravitational force | unconditional | where is the mass and is the acceleration due to gravity | vertically downward, hence an angle with the normal to the incline and an angle with the incline | |

tension | unconditional | needs to be computed based on solving equations. | pulls the mass up the inclined plane. | |

normal force | unconditional | adjusts so that there is no net acceleration perpendicular to the plane of the incline | outward normal to the incline | |

static friction | no sliding | adjusts so that there is no net acceleration along the incline. At most equal to . | The direction could be either up or down the incline, depending on whether the remaining forces create a net tendency to pull down or pull it up. | |

kinetic friction | sliding | where is the normal force | opposite direction of motion -- hence down the incline if sliding up, up the incline if sliding down. |

### Components perpendicular to the respective inclined planes

For more analysis of this part, see sliding motion along an inclined plane#Component perpendicular to the inclined plane

For , taking the component perpendicular to the inclined plane , we get:

For , taking the component perpendicular to the inclined plane , we get:

Note that this part of the analysis is common to both the *sliding* and the *no sliding* cases.

### Components along the respective inclined planes assuming no sliding

Note that the *no sliding* case has two subcases:

- The system has a
*tendency*to slide down and up, i.e., this is what would happen if there were no static friction. Thus, the static friction acts*up*the incline and the static friction acts*down*the incline . - The system has a
*tendency*to slide up and down, i.e., this is what would happen if there were no static friction. Thus, the static friction acts*down*the incline and the static friction acts*up*the incline .

Let's consider the first case, i.e., down and up. We get the equation for :

and

We get a similar equation for :

and

Add (2.1) and (2.3) and rearrange to get:

Plugging in (2.2) and (2.4) into (2.5), we get:

Plugging in (1.1) and (1.2) into this yields:

Cancel from all sides to get:

This is the necessary and sufficient condition for the system to have a *tendency* to slide down and up, but to not in fact slide.

Simialrly, in the other not sliding case (i.e., the system has a tendency to slide down, up), we get the following necessary and sufficient condition:

Overall, for the no sliding case, we get the necessary and sufficient condition:

Note the following: in all these cases, it is *not* possible, using these equations, to determine the values of , and individually.

### Components along the respective inclined planes assuming sliding

We consider two cases:

- is sliding (and accelerating) down and is sliding (and accelerating) up, so the force of kinetic friction acts
*up*along and the force of kinetic friction acts*down*along . - is sliding (and accelerating) up and is sliding (and accelerating) down, so the force of kinetic friction acts
*down*along and the force of kinetic friction acts*up*along .

We first consider the down, up case. Let denote the magnitude of acceleration for . is also equal to the magnitude of acceleration for . We get:

with

and

with

Add (3.1) and (3.3), plug in (3.2),(1.1) and (3.4),(1.2) to get:

Rearranging, we get:

Since by our sign convention, this case is valid if:

and in particular:

The other case ( down, up) occurs if the inequality sign is reversed, and we get, in that case, that: